Produkte filtern
–
von
4 €
bis
291 €
Produkte filtern
–
von
4 €
bis
291 €
60 Produkte
60 Produkte
Allgemeine DatenRohrdurchmesser50-51 mmBelastbarkeit (WLL)--- FarbeAluminiumBauformClaw ClampAbgangAbgang41,5mm Plug - schweißbar mit Rohr 50x4mm/48x3mmTechnische DatenBreite50 mmZugbelastung---MaterialAluminium 6061 T6Gewicht 0,26 kgZusätzliche InformationVerpackungseinheit35 Stück
Two frame clamps available for holding frames up to 25mm and 50mm thick. Supplied fitted with a 10mm pin.
Aluminium side clamp plates powder painted, black one side, white reverse. 10mm diameter pin for use with Gripheads. Captive securing pins. Used predominantly to hold polystyrene boards.
A range of arms and headers fitted with 29mm spigots and receivers.
A 90 degree connection between two tubes. This Pipeclamp fitting cannot be used to join tubes in the top of the short tee. For joining tubes Pipeclamp fitting T10400 should be used. Tube Diameter: 48mm Weight: 0.53 Kg
A three way enclosed 90 degree corner joint. Tube Diameter: 48mm Weight: 1.18 Kg
A Termination flange to be used on structures where a positional fixing only is required. 8mm mounting holes. This fitting is not recommended for use as a base plate for Guard railing, see T13200. Tube Diameter: 48mm Weight: 0.85 Kg
Eine Wandhalterung für Handläufe. Diese Halterung kann keine Rohre verbinden.Montagebohrungen: 8mmRohrdurchmesser: 48mmGewicht: 0,63 Kg
A complete single swivel.The swivel has a travel of approximately 85 degrees in each direction.Tube Diameter: 48mmWeight: 0.98 Kg
A 90 degree connection between two tubes. This can be used to join two tubes in the top of the twin grub screw long tee. Tube Diameter: 48mm Weight: 0.30 Kg
A three way enclosed 90 degree corner joint. Tube Diameter: 48mm Weight: 0.33 Kg
A 90 degree corner fitting with through tube. Tube Diameter: 48mm Weight: 0.25 Kg
A Termination flange to be used on structures where a positional fixing only is required. This fitting is not recommended for use as a base plate for Guard railing. Tube Diameter: 48mm Weight: 0.35 Kg
A structural base plate for all aspects of vertical tube support. The holes in the base plate are large enough to enable the use of mechanical or chemical anchor fixings. Tube Diameter: 48mm Weight: 0.27 Kg
Structural flush side palm fixing. The flush design enables tubes to be tight to the structure. Tube Diameter: 48mm Weight: 0.35 Kg
A wall mounting bracket for handrails. This fitting has no ability to join tubes. Tube Diameter: 48mm Weight: 0.30 Kg
A pressed steel clamp used to secure two scaffold cross over tubes. Tube Diameter: 48mm Weight: 0.59 Kg
A range of steel boom arms. Available with a safety bond anchor point. Fits Tubes: 48 - 51mm Centres: 280mm from pipe centre to hole centre
Available in two sizes for 32mm and 48mm tubes. Can be supplied with or without plate with threaded hole. Fits Tubes: 32mm or 48mm Finish: Zinc Plated
A horizontal lighting bar used with a Tee Bar bolt fixing stand top. Fixings: M12 Bolts & Wing Nuts supplied Weight: 0.80 Kg
Drop-Arm mit fester Länge, 29-mm-Zapfen und 29-mm-Aufnahme. Durch die offene Bauweise kann die Leuchte um 360° gedreht werden, während sie durch den Sicherungsstift sicher gehalten wird.Zapfen: 29 mmFarbe: schwarzLänge: 500 mmGewicht: 2,17 kg